Re: Setting up new bunk trailer I like to position the bunks just outside lifting strakes, actually touching the outside of them. Before you begin, offload the boat into the water where you can dock it for a few hours. Usually this is a simple matter of attaching the brackets to the trailer frame (unless you're reusing the old ones) and the boards to the brackets. BTW, IMO the slide-hole brackets are better. Bunk brackets attached directly to the pontoon trailer main frame cross members are the strongest. 17 results for boat trailer support brackets Save boat trailer support brackets to get e-mail alerts and updates on your eBay Feed. Champion Trailers offers a large variety of replacement boat trailer bunk boards, bunk board hardware & accessories Bunk carpet, swivel bolster brackets, vertical bunk brackets, timber brackets, book end style brackets, 4x6 timber brackets, EZ Loader bunk brackets, adjustable bunk bolsters, pontoon trailer bunk brackets and other bunk supports. How To Adjust Boat Trailer Bunks. Boat trailer self centering glider kits are designed to attach to each of your boat trailers cross sections.

I've provided a photo showing how the bunk board attaches to the bracket, which should answer all … BoatTrailerParts.com Brought to … The CE Smith Galvanized Bolster and Swivel Mounting Brackets for Bunk Boards # CE10001G-4 come with nuts and bolts to attach the swivel brackets to the bolster brackets, but you will need to supply either lag bolts or other through bolt hardware to attach these assemblies to the wooden bunks on your boat trailer and the trailer frame. Unfollow boat trailer support brackets … More brackets distribute the weight of the pontoon boat evenly along the length of the frame. This 10 inch Hot-Dipped Galvanized Swivel Top Bunk Bracket kit is designed for boat trailer bunk board set ups that commonly use Bunk Board 2 in x 4 in sets and also to adjust the angle to the contour of the boat hull.


Check out Load Rite's online store for a selection of bunk brackets for your boat trailer.

The weight of the boat is carried on the cross member, not on some piece of steel welded onto the outside of the frame.

Since you don't need a swiveling bracket, the # CE10600G bracket you mentioned would work fine. Re: bunk bracket, is this safe to install Further to those bumps; if you mount so that the flat side of the new bracket mates to the OTHER side of the c-channel in your frame, those bumps catch the edge of the c-channel and prevent sliding.
Unless a trailer is specifically built for a specific boat, attach bunk systems (either roller or bunk style) to the framework of the trailer with adjustable mounting brackets. Install the bunk boards following manufacturer recommendations. The more brackets the better. Ranging in length between 300 to 500mm long (pending the size of your boat and trailer), these kits come complete so all you need to do is attach them to your trailer, make the adjustments to the angles to guide down to your keel rollers. To a degree, the brackets enable you to raise, lower or move the bunks side to side and enable you to adjust the angle of the bunk to match the sloped bottom on a V-hulled watercraft. Like your boat; your boat trailer’s bunks, the Plastic, PVC or Carpet adjustable skids the boat sits on while on the trailer will occasionally require adjustment’s to carry the load of your boat properly.

The bunk brackets will attach to the trailer cross members using U-bolts. A lot of boats have stringers molded in at the point of the strakes, especially the ones a couple of feet from the keel which is a good place to place a bunk for stability. Typically, these adjustable swivel bunk board brackets are mounted to cross members in front and behind the axle, a common single axle trailer might have (4) of these. Boat Trailer Bunk Brackets come in both Galvanized and Aluminum and mounted your Boat Trailers Bunk Posts or Post Supports to Guide your Boat on the Trailer and Support you Boats Hull, available in many styles and sizes. 1-16 of 218 results for "Boat Trailer Bunk Brackets" Price and other details may vary based on size and color Sturdy Built (2) 8" Galvanized Swivel Top Bunk Bracket Kit with Hardware for 3x3 Boat Trailer …